Jaltest 22.2 Update

Written By Kevin Vieth

The second software update of the year was released today (July 5th, 2022) and Cojali has yet again packed in an amazing amount of new makes, models, functionalities and service information. WholeFleet is here to provide you with a bullet point summary of some of the key additions to the software broken down for each module:

Commercial Vehicle

  • Bendix

    • ABS/ATC U1X braking system, bi-directional tests, maintenance reset and 25 new troubleshooting guides

  • Caterpillar

    • support for new *.trim file format and engine type technical data for several engines such as C-7, C-9, C-12, etc.

  • Cummins

    • extended engine model coverage. More than 100 new procedures to check systems and their components have been added.

    • GHG 21 CM2450 engine systems (L9, B6.7, X12, X15). SCR efficiency test, EGR Differential Pressure Reset for FC-1866

    • Natural Gas ISX12N CM2380 engine control system, new component replacement guides with helpful images.

  • Dana

    • TPMS tire inflation and monitoring system including wiring diagrams, technical data, component images, manual diagnostics and much more.

  • Detroit

    • DDEC20 Gen 5 GHG21 vehicles: More than 500 SMART guides for the main systems ACM3, CPC5 and MCM2.1.

  • Freightliner

    • New Cascadia module identification enhancements and new technical data

  • International

    • WorkStar and DuraStar Body Builder Connector diagrams

  • Navistar

    • A26 GHG21 engine control system, complete coverage for 2021 and newer engines including technical data, wiring diagrams, troubleshooting guides, maintenance services, calibrations, etc.

  • Volvo

    • VECU 5 GHG21 coverage for 2022 models.

    • ACM exhaust gas aftertreatment system, AdBlue/DEF pressure build-up and Retarder pressure check.

  • Dodge

    • RAM 2018 and newer models equipped with HEMI 5.7/6.4 L V8 engine. SGW unblocking available.

  • HINO

    • New systems coverage, the Inverter and the Battery controllers.

  • Isuzu

    • extended coverage for 4JJ1-TC and 4HK1-TC (on K line) engine control systems installed in several models.

Off-Highway/Construction Equipment

  • New Cable Adaptors (JDC 560A9 and JDC 561A9) for Isuzu engines in HITACHI and JOHN DEERE CE machines.

  • Caterpillar

    • C-4.4 and C-6.6 (on CDL) engine control systems, check of the turbocharger wastegate valve.

    • ARD exhaust gas aftertreatment system, air metering check of the exhaust gas aftertreatment system.

    • EHCU (on SAE J1939) hydraulic control system, calibrations.

    • MCM central computer for D Series dozers, transmission calibration, service brake calibration and steering control joystick calibration.

  • Terex

    • Allison CEC2 5000/6000/8000/9000 Series transmission

  • Volvo

    • V2ECU vehicle electronic control unit, float valve check and parameter setting of the raising/lowering and loading/dumping control valves

  • XCMG

    • EDC V2 Volvo engine control system, idle speed setting and injector coding.

  • Bobcat

    • Gateway module for E Series compact excavators & IC instrument cluster for 430 Series compact excavators.

  • Case CE

    • Wiring diagram settings of the EDC 17 C49 engine control system for TR 300 Series and TV 300 Series models, and EDC 7 UC31 engine control system for SR 220 Series and SR 250 Series skid-steer loaders.

  • JCB

    • ECM (on SAE J1939) Perkins 403J/404J engine control system, injector test, intake/exhaust valve check, injection rail pressure test, etc.

    • Transmissions for CX Series models, extension of measurements, control solenoid valve activation and warning lamp activation.

    • DieselMax 430 (Stage V)

  • Cummins

    • QSF 2.8/3.8 CM2880 4D95 3.3 CM2350 F3.8 CM2350 coverage

  • Volvo Penta

    • EMS V3 & EDC V2 functionality expansion

  • Yanmar

    • EDC Denso engine control system, Diesel Oxidation Catalyst replacement (DOC).

Material Handling Equipment

  • Caterpillar

    • LOGICS central computer (on RS232) for electric forklifts.

  • Genie

    • EMR4-EDC 17 CV52 engine control system, throttle valve check in the intake manifold, diesel particulate filter replacement and soot content reset.

  • Haulotte

    • ECM Kohler Stage V engine control system, throttle valve check in the intake manifold, diesel particulate filter replacement and engine shutdown.

  • Jungheinrich

    • LMC power management system for traction, parameter setting of the travel speed and brake system. HCU control system of the hydraulic system, parameter setting of the auxiliary spool valves, mast and hydraulic pump, etc.

  • Linde

    • LAC power management system for traction that includes advanced functions of parameter setting and calibrations such as the tiller potentiometer calibration and the accelerator calibration

  • Still

    • MCU central computer (on RS232) for latest generation forklifts that includes advanced functions such as the control lever calibration or the steering angle sensor calibration, among others.

Agricultural Vehicles

  • Bobcat models added to this module

  • Farmall

    • A Series, engine: Interim Tier 4/Stage IIIB Farmall Series, engine: Tier 5/Stage V Luxxum Series, engine: Tier 5/Stage V coverage added

  • Challenger

    • MT 700 Series, engine: Tier 5/Stage V coverage added

    • EEM4 - EDC 17 CV41 engine control system in MT 800E Series models, aftertreatment system fault clearing.

  • Fendt

    • 1000 Vario MT Series, engine: Final Tier 4/Stage IV coverage added

  • Kubota

    • M4N Series M6H Series L3 and L4 Series coverage added

  • Massey Ferguson

    • 2600 H Series coverage added

  • New Holland

    • T3LP Series, engine: Tier 5/Stage V T4 V/N/F/LP Series, engine: Tier 5/Stage V T5 Series - Electro Command, engine: Tier 5/Stage V

  • Case IH

    • Calibration procedures of the SFA front suspension control system, the Trans transmission and the RPTO rear power take-off.

  • Claas

    • HLHP central computer in the Atos (A78/A79/A98/A99) model, calibrations.

  • Deutz-Fahr

    • Calibrations and maintenance resets of the transmission oil change, the transmission oil filter, and the spool valve oil change in the SECU system in 6 Series and 7 Series models.

  • Fendt

    • MAN EDC 17 CV42 engine control system in 1000 Vario Series and 900 Vario Series (GEN6) models, injector coding and AdBlue/DEF filter replacement.

  • John Deere

    • EDC Denso Yanmar engine control system in 3E Series, 3R Series, 4M Series and 4R Series models, Diesel Oxidation Catalyst replacement (DOC).

    • additional functionalities added

Marine Vessels

  • Crusader

    • EMC GCP engine control system that includes new system measurements with catalytic converter, and system checks such as the cylinder cut-out or the idle speed test. It also has the system counter reset and the adaptation value reset.

  • Ilmor

    • ECM MV8 engine control system that includes new system measurements with catalytic converter, and system checks such as the cylinder cut-out or the idle speed test. It also has the system counter reset and the adaptation value reset.

  • Indmar

    • ECM EControls engine control system coverage added.

  • Malibu

    • ECM G4 engine control system that includes new system measurements with catalytic converter, and system checks such as the cylinder cut-out or the idle speed test. It also has the system counter reset and the adaptation value reset.

  • Mercury / Mercruiser

    • Wiring diagram settings, technical data and location images for the G3 engine control systems in the following models: 4.5 L 200 ECT, 4.5 L 250 ECT, 6.2L 300, 6.2L 300 ECT, 6.2L 320

This is not a complete list of all changes and additions to the Jaltest software with this update. To see a demo of Jaltest 22.2 please book with the WholeFleet team at a time that works for you: BOOK NOW

Kevin Vieth

Kevin Vieth founded VieTech Training & Consulting Inc. in 2016 out of a passion for empowering heavy-duty and automotive service technicians through technical training. Due to the fast pace of technological advancements, he believes that on-going knowledge and skill development is imperative. With the operational pressures applied to business managers, skills training can be inconvenient, inaccessible and costly. This motivated Kevin to develop the Diesel Engine Technology Fundamentals in-class training curriculum to provide relevant and realistic diesel technology diagnostic training that is on-site, on-time and on-budget.

As a former technical Training Instructor for Cummins Western Canada, Kevin has delivered over 125 Cummins engine certification courses to over 500 heavy-duty technicians. Prior to his time with Cummins, he worked as a journeyman 310S automotive technician and then spent 3 years as a technical lead for Westport Innovations, a world leader in natural gas fuel system development. Kevin’s experience as a service technician, combined with his knowledge of fuel, emissions and engine controls acquired at Westport, helped him excel as a Cummins trainer and in diesel engine fault troubleshooting.

In addition to delivering on-site diesel engine diagnostic training to fleets nation-wide, Kevin also provides on-going remote troubleshooting and technical support to his clients.

https://www.vietech.ca
Previous

Jaltest 22.3 Update
Next

Jaltest vs TEXA: Which Is The Best Vehicle Diagnostic Software